Contents:

• 18 Feet 0 AWG Blue Kolossus Fleks Power Wire
• 5 Feet 0 AWG Black Kolossus Fleks Ground Wire
• One FH-20 with Choice of Fuse size
• 3 Black / 1 Red 0 Gauge ring terminals
• 5 feet Split Loom and wire ties

Note: this kit does not contain any RCA interconnect cables or speaker wire. If you need RCA cables, check out the recommended KnuKonceptz Klarity RCA Cable 2 Channel RCA Interconnect Cable here.

Power Rating:

KnuKonceptz does not use “watts” to rate our amp kits. This is a very inaccurate method to determine what the proper gauge wire required for your amp installation. There are many car audio amplifier manufactures and not all of them represent the output of their product accurately. Please refer to your amplifier’s fuse rating, this is a number a manufacture can not fake, well they could but it would put their product in harms way! Add up the fuses on the end of both of your amp (ex Amp A has three 40A fuses = 120A draw; Amp B has two 30A fuse = 60A Draw; 180A system total draw) If this number is under 300A, this kit will fit your application.

Wire Size Calculator: https://caraudioadvice.com/calculators/

Additional Information:

Kolossus Fleks 0 Gauge Power Amp Installation Kit. This kit is designed to be a base for installation of a large, high current audio system. Once again KnuKonceptz includes additional 0 gauge ground wire to allow for Battery to Chassis Ground Upgrade, a signature of a KnuKonceptz 0 Gauge kit:

• Your vehicle’s wiring was engineered to work with the factory electrical load. By adding a massive current drawing load requiring a heavy 0 gauge power wire, you also need to upgrade the vehicle’s ground wire. This kit includes the appropriate parts to complete this upgrade. The 5′ section of ground should be cut one time (to make two sections). These do not need to be even length, but rather cut to fit your installation’s need. You may only need 18″ to connect the battery to your vehicles chassis. The remaining 0 gauge ground wire is then used to connect the audio amplifier to your car’s chassis.

KnuKonceptz Kolossus amp installation kits feature our top of the line Kolossus Fleks power and ground cables. Made up of ultra flexible pvc and ultra fine tinned strands of oxygen free copper (OFC), the Kolossus Kable is the standard for which all others are compared to. The KFX-PK0 amp power kit provides 18 feet of blue marine grade full copper battery power wire and 5 feet of translucent black (smoke) ground wire. The KnuKonceptz FH-20 fuse holder comes with your choice of fuse size (see the FAQ to determine what size is right for you.)The fuse holder does not come installed within the cable, this allows the installer to place the inline fuse holder in an optimum location during installation. It also allows the installer to extend the power wire 1-3′ by using the inline fuse holder to add cable to the main run (leaving the 18′ as one unit and using the FH-20 to “splice” a few extra feet of wire should your installation require a longer run)

Contents:

• Power Wire: 18 Feet Tinned OFC 8 Gauge Ultra Flex Blue
• Ground Wire: 3 Feet Tinned OFC 8 Gauge Ultra Flex Black
• Fuse Holder: In Line with 60A Mini-ANL Fuse
• RCA Cable: 17 Feet Klarity coaxial 2 Channel RCA
• Remote Wire: 17 Feet Blue Turn on lead
• Speaker Wire: 20 Feet Kord OFC Blue 14 Gauge Speaker Wire
• Terminals: 4 Gauge Gold Plated Ring Terminals(2), 4 Gauge Gold Plated Spade Terminals(2)
• Wire ties and bushings

Note: this kit contains one (1) 2 channel RCA interconnect cable. If you need additional RCA cables, check out the recommended KnuKonceptz Klarity RCA Cable 2 Channel RCA Interconnect Cable here.

Power Rating:

KnuKonceptz does not use “watts” to rate our amp kits. This is a very inaccurate method to determine what the proper gauge wire required for your amp installation. There are many amp manufactures and not all of them represent the output of their product accurately. Please refer to your amplifier’s fuse rating, this is a number a manufacture can not fake, well they could but it would put their product in harms way! Add up the fuses on the end of your amp (two 25A fuses = 50A total draw) If this number is under 60A, this kit will fit your application. If over 60A, this amp install kit will not work for that application, that installation would require 4 gauge or larger wire.

Wire Size Calculator: https://caraudioadvice.com/calculators/

Additional Information:

KnuKonceptz Kolossus amp installation kits feature our top of the line Kolossus Fleks power and ground cables. Made up of ultra flexible pvc and ultra fine tinned strands of oxygen free copper (OFC), the Kolossus Kable is the standard for which all others are compared to. The KOL-AK8 amp kit provides 18 feet of blue marine grade, full copper battery power wire and 3 feet of translucent black (smoke) ground wire. The KnuKonceptz FH-44 fuse holder with a 60A Mini ANL fuse is provided within the KOL-AK8 amp install kit. The fuse holder does not come installed within the cable, this allows the installer to place the inline fuse holder in an optimum location during installation. It also allows the installer to extend the power wire 1-3′ by using the inline fuse holder to add cable to the main run (leaving the 18′ as one unit and using the FH-44 to “splice” a few feet of wire)

Signal for your 2 channel amplifier installation kit is carried by the Klarity Kable 5 Meter (16.25′) RCA Cable. The Klarity RCA Cable is a copper braid shielded coaxial RCA that uses a Hybrid metal/molded RCA termination with strain relief for a durable, low loss connection to your head unit and amplifier. A separate remote turn on lead is included. This wire is connected to your radio’s power antenna lead or amp turn on lead (refer to your head unit’s manual) Your amplifier’s output is sent through KnuKonceptz Kord 14 gauge speaker wire, 20 feet of 14 gauge blue speaker wire is included with the kit.

Contents:

• 16.5 Feet 4 Gauge Ultra Flex Blue Tinned Oxygen Free Copper Power Wire
• 3 Feet 4 Gauge Ultra Flex Black Tinned Oxygen Free Copper Ground Wire
• One inline fuse holder with 120A Mini ANL Fuse
• One 17 Foot OFC Klarity 2 Channel RCA Cable
• One 17 Foot OFC Remote Turn On Lead
• 20 Feet BLUE Kord Kable OFC 12 Gauge Speaker Wire
• 2 gold plated 4 gauge ring terminals, 2 gold plated 4 gauge spade terminals
• grommets and wire ties

Note: this kit contains one (1) 2 channel RCA interconnect cable. If you need additional RCA cables, check out the recommended KnuKonceptz Klarity RCA Cable 2 Channel RCA Interconnect Cable here.

Power Rating:

KnuKonceptz does not use “watts” to rate amp kits. This is a very inaccurate method to determine what the proper gauge wire required for your amp installation. There are many amp manufactures and not all of them represent the output of their product accurately. Please refer to your amplifier’s fuse rating, this is a number a manufacture cannot fake, well they could but it would put their product in harms way! Add up the fuses on the end of your amp (three 25A fuses = 75A total draw) If this number is under 120A, this kit will fit your application. If over 120A, but less then 150A, this kit will work, but a 150A mini-ANL fuse is required (sold separately). If over 150A, this amp install kit will not work for that application, that installation would require 2 gauge or larger wire.

Wire Size Calculator: https://caraudioadvice.com/calculators/

Additional Information:

KnuKonceptz Kolossus amp installation kits feature the top of the line Kolossus Fleks power and ground cables. Made up of ultra flexible pvc and ultra fine tinned strands of oxygen free copper (OFC), the Kolossus Kable is the standard for which all others are compared to. The KOL-AK4 amp kit provides 18 feet of blue marine grade, full copper battery power wire and 3 feet of translucent black (smoke) ground wire. The KnuKonceptz FH-44 fuse holder with a 120A Mini ANL fuse is provided within the KOL-AK4 amp install kit, but can be upgraded to a maximum of 150A Mini ANL fuse (sold separately MANL-150). The fuse holder does not come installed within the cable, this allows the installer to place the inline fuse holder in an optimum location during installation. It also allows the installer to extend the power wire 1-3′ by using the inline fuse holder to add cable to the main run (leaving the 18′ as one unit and using the FH-44 to “splice” a few feet of wire).

Signal for your 2 channel amplifier installation kit is carried by the Klarity Kable 5 Meter (16.25′) RCA Cable. The Klarity RCA Cable is a copper braid shielded coaxial RCA that uses a Hybrid metal/molded RCA termination with strain relief for a durable, low loss connection to your head unit and amplifier. A separate remote turn on lead is included. This wire is connected to your radio’s power antenna lead or amp turn on lead (refer to your head unit’s manual). Your amplifier’s output is sent through KnuKonceptz Kord 12 gauge speaker wire, 20 feet of 12 gauge blue speaker wire is included with the kit.

• Oxygen Free Copper Signal Path
• Full Braid Shield
• Gold Plated Hybrid Metal/Molded RCA ends

The Klarity RCA Cable is a copper core, braid shielded coaxial RCA that uses a Hybrid metal/molded RCA termination with strain relief for a durable, low loss connection to your head unit and amplifier. Features include an easy to grip injection molded end that is also color coded for quick channel identification.